|
Message ID
|
Severity
|
Message
|
|
XSTRM-1
|
Warning
|
Value of pin attribute number is out of range 1-127. Pins will not be preserved.
|
|
XSTRM-2
|
Error
|
Library name '%s' is invalid in UNIX namespace.
|
|
XSTRM-3
|
Error
|
Tech library name '%s' is invalid in UNIX namespace.
|
|
XSTRM-4
|
Error
|
Failed to locate run directory '%s'. Check that the directory exists and that you have permissions to write in this directory.
|
|
XSTRM-5
|
UN-USED
|
Run directory '%s' does not exist or is not a directory.
|
|
XSTRM-6
|
Error
|
Failed to open the template file '%s'. Check that the template file exists and is a regular UNIX file.
|
|
XSTRM-7
|
Error
|
Failed to open cell name map file '%s'. Check that the file exists in the run directory and that you have permission to read it.
|
|
XSTRM-8
|
Error
|
Failed to open text font map file '%s'. Check that the file exists in the run directory and that you have permission to read it.
|
|
XSTRM-9
|
Error
|
Failed to open property map file '%s'. Check that the file exists in the run directory and that you have permission to read it.
|
|
XSTRM-10
|
Error
|
Failed to open layer map file '%s'. Check that the file exists in the run directory and that you have permission to read it.
|
|
XSTRM-11
|
Error
|
Failed to open refLibList file '%s'. Check that the file exists in the run directory and that you have permission to read it.
|
|
XSTRM-12
|
UN-USED
|
Failed to open pinTextMap file '%s'. Check that the file exists in the run directory and that you have permission to read it.
|
|
XSTRM-13
|
Error
|
Failed to open input Stream file '%s'. Check that the file exists in the run directory and that you have permission to read it.
|
|
XSTRM-14
|
Error
|
Failed to open ASCII technology file '%s'. Check that the file exists in the run directory and that you have permission to read it.
|
|
XSTRM-15
|
Error
|
Failed to create Stream file '%s' in the run directory. Check that you have permission to create this file.
|
|
XSTRM-16
|
Error
|
Failed to create summary file '%s' in the run directory. Check that you have permission to create this file.
|
|
XSTRM-17
|
Error
|
Failed to create log file '%s' in the run directory. Check that you have permission to create this file.
|
|
XSTRM-18
|
Warning
|
Performing automatic layer mapping because either the layer mapping information is missing or the '-layerMap' option is using the XST_AUTO_LM value. However, failed to create the automatic layer map file '%s' in the run directory. Ensure that you have the write permission to create this file.
|
|
XSTRM-19
|
Warning
|
Failed to create the automatic cell name map file '%s' in the run directory. Ensure that you have the write permission to create this file.
|
|
XSTRM-20
|
Warning
|
Output Stream file '%s' already exists. It will be overwritten.
|
|
XSTRM-21
|
Error
|
Failed to open the library '%s'. Check that library is present in the path defined in the 'cds.lib' file.
|
|
XSTRM-22
|
Error
|
Failed to open the technology file '%s' from library '%s'. Check that the library exists in the location defined in the 'cds.lib' file and that you have read permission to the technology file.
|
|
XSTRM-23
|
UN-USED
|
Purpose '%s' is not defined in the technology file. All the blockages in the design will be considered on purpose 'boundary'.
|
|
XSTRM-24
|
UN-USED
|
Purpose '%s' is not defined in the technology file. All the blockages in the design will be considered on purpose 'drawing'.
|
|
XSTRM-25
|
Warning
|
The layer map file '%s' contains an invalid record at line number '%d' and will be ignored. This is because the format of the mapping entry in the layer map file '%s' is invalid. The valid mapping entry format is: <layerName purposeName strmLayer strmType [Material [MaskNumber]] [Qualifier] [PhotomaskColor ColorState]>, where 'PhotomaskColor' and 'ColorState' are valid only when the '-enableColoring' option is set and the permissible range for strmLayer and strmType is 0 - %d. Now, update the mapping entry and then translate again.
|
|
XSTRM-26
|
Warning
|
The font map file '%s' contains an invalid record at line number '%d' and will be ignored. This is because the format of the mapping entry in the font map file '%s' is invalid. Update the mapping entry format to: <fontNumber fontName> and try again.
|
|
XSTRM-27
|
Warning
|
The property map file '%s' contains an invalid record at line number '%d' and will be ignored. This is because the format of the mapping entry in the property map file '%s' is invalid. Update the mapping entry format to: <strmAttribute objectType propName> and try again.
|
|
XSTRM-28
|
Warning
|
The cell map file '%s' contains an invalid record at line number '%d' and will be ignored. This is because the format of a mapping entry in the cell map file '%s' is invalid. Update the mapping entry format to: <libName cellName viewName structName> and try again.
|
|
XSTRM-29
|
Warning
|
The refLib file contains invalid record at line number %d. This record in the refLib file will be ignored.
|
|
XSTRM-30
|
UN-USED
|
|
|
XSTRM-31
|
Warning
|
Layer map file '%s' contains a duplicate entry for Stream layer-datatype '%d:%d' at line '%d'. Therefore, this entry will be ignored during translation.
|
|
XSTRM-32
|
Warning
|
The layer map file '%s' contains unknown layer '%s' at line number '%d' and will be ignored. This is because the layer name specified in the layer map file is not defined in the technology file. Ensure that the layer name specified in the layer map file is both valid and defined in the technology file.
|
|
XSTRM-33
|
Warning
|
The layer map file '%s' contains unknown purpose '%s' at line number '%d' and will be ignored. This is because the purpose name specified in the layer map file is not defined in the technology file. Ensure that the purpose name specified in the layer map file is both valid and defined in the technology file.
|
|
XSTRM-34
|
Warning
|
The objects in the layer-purpose pair '%u:%u' are ignored. This is because either the layer-purpose pair used in the design is not specified in the layer map file or the layer/purpose is not defined in technology file. Ensure that the layer-purpose pair used in the design is specified in the layer map file and the layer/purpose is defined in technology file.
|
|
XSTRM-35
|
Warning
|
The objects in the layer-purpose pair '%s:%s' are ignored. This is because the layer-purpose pair used in the design is not specified in the layer map file. Specify the layer-purpose pair in the layer map file and try again.
|
|
XSTRM-36
|
Warning
|
The objects in the stream layer-datatype '%d:%d' are ignored. This is because the stream layer-datatype pair is either not specified in the layer map file or the entry is invalid and was therefore ignored. Specify the stream layer-datatype pair in the layer map file or correct the wrong entry and try again.
|
|
XSTRM-37
|
UN-USED
|
Layer-datatype range is exhausted. All the shapes on layer-purpose pair '%d:%d' will be ignored.
|
|
XSTRM-38
|
Warning
|
The library %s in the refLibList file %s could not be found. This is because the library '%s' specified in refLibList file does not exist. Ensure that the library '%s' is defined in the library definition file and also exists in the location specified in the library definition file.
|
|
XSTRM-39
|
Warning
|
The font map file contains invalid font name '%s' at line number %d. The valid font names are: EuroStyle, Gothic, Math, Roman, Script, Stick, Fixed, Swedish, and MilSpec. Specify a valid font name and try again.
|
|
XSTRM-40
|
Warning
|
The font map file contains invalid Stream font number '%d' at line number %d. The valid font numbers are: 0, 1, 2, and 3. Specify the valid font numbers and try again.
|
|
XSTRM-41
|
Warning
|
The property map file '%s' contains invalid record at line number '%d'. The valid object types are: Dot, Pin, Line, Path, Polygon, Rect, Text, ArrayInst, ScalarInst, Arc, Donut, Ellipse, PathSeg, Route, Marker, Row, AreaBoundary, PRBoundary, SnapBoundary, ClusterBoundary, AreaBlockage, AreaHalo, LayerBlockage, and LayerHalo. Specify the valid object types and try again.
|
|
XSTRM-42
|
Warning
|
The property map file '%s' contains an invalid format at line number '%d' and will be ignored. The valid mapping entry format is [<-fp/-fv> SP_CH_OPTSEP <-s 'property separator'>]. If '-fp' option is specified during StreamOut, properties are written as <name:value> pairs; and during GDSII/StreamIn, properties are assumed to be present in the stream file as <name:value> pairs. If '-fv' option is specified during StreamOut, only values of properties are written in the property map file. You can also specify the property separator as [-s 'property separator'] without using '-fp' or '-fv'.
|
|
XSTRM-43
|
Warning
|
Stream Attribute %d specified in the property map file conflicts with the value of '-pinAttNum' option. This entry will be ignored.
|
|
XSTRM-44
|
UN-USED
|
Pin text map file contains an unknown layer '%s' at line '%d'. This entry in the pin text map file will be ignored.
|
|
XSTRM-45
|
Warning
|
Mapping for layer '%d' will not be written in %s file because layer '%d', which is used in the input design is not defined in the technology file. Ensure that the layer exists in the technology file or use the correct technology file.
|
|
XSTRM-46
|
Warning
|
Mapping for purpose '%d' will not be written in %s file because purpose '%d', which is used in the input design is not defined in the technology file. Ensure that the purpose exists in the technology file or use the correct technology file.
|
|
XSTRM-47
|
Warning
|
Library '%s' is used in the design but does not exist. It will not be listed in the summary file.
|
|
XSTRM-48
|
Error
|
Failed to flatten the Pcell instance '%s' in the cellview '%s/%s/%s'. XStream Out flattens Pcell instances when the Flatten Pcells option is used. Ensure that the Pcell instance is correct by opening the cellview '%s/%s/%s' and flattening the instance in Virtuoso.
|
|
XSTRM-49
|
Error
|
The pin information could not be translated. This is because the value 'text' is specified for the Convert Pin To option and Stream Out is unable to get the ID associated with the pin connected with the figure at origin (%d, %d). Rectify the input database to prevent data corruption and translate again.
|
|
XSTRM-50
|
Error
|
The pin information could not be translated. This is because the Pin Attribute Num option is specified during Stream Out to translate the pin information, and Stream Out was unable to get the ID associated with the pin connected with the figure at origin (%d, %d). Rectify the input database to prevent data corruption and translate again.
|
|
XSTRM-51
|
Error
|
The pin information could not be translated. This is because the value 'text' is specified for the Convert Pin To option and Stream Out was unable to get the pin name associated with the pin connected with the figure at origin (%d, %d). Rectify the input database to prevent data corruption and translate again.
|
|
XSTRM-52
|
Error
|
The pin information could not be translated. This is because the Pin Attribute Num option is specified during Stream Out to translate the pin information, and Stream Out was unable to get the pin name associated with the pin connected with the figure at origin (%d, %d). Rectify the input database to prevent data corruption and translate again.
|
|
XSTRM-53
|
Error
|
The pin information could not be translated. This is because the Pin Attribute Num option is specified during XStream Out to translate the pin information, and XStream Out was unable to get the term name associated with the pin. Rectify the input database to prevent data corruption and translate again.
|
|
XSTRM-54
|
UN-USED
|
Symbolic pins will not be translated as text because pinTextMap file is not provided.
|
|
XSTRM-55
|
Warning
|
Vector instance '%s' encountered. It will be translated as SREF in the Stream file.
|
|
XSTRM-56
|
Warning
|
Library '%s' specified in cell map file is not present in refLibList, its mapping will be replaced with the target library.
|
|
XSTRM-57
|
Warning
|
Failed to create the new layer '%s'. All the shapes on this layer will be dropped.
|
|
XSTRM-58
|
Warning
|
Failed to create the new layer-purpose pair '%s:%s'. It will be skipped and all the shapes on this layer-purpose pair will be dropped.
|
|
XSTRM-59
|
Warning
|
Failed to create the new purpose '%s'. All the shapes on this purpose will be dropped.
|
|
XSTRM-60
|
Info
|
Creating a new purpose %s in the technology file.
|
|
XSTRM-61
|
Info
|
Creating a new layer %s in the technology file.
|
|
XSTRM-62
|
Info
|
Creating a new layer-purpose pair '%s:%s' in the technology file.
|
|
XSTRM-63
|
Warning
|
Failed to set the 'visibility attribute' of a newly created layer-purpose pair '%s:%s'.
|
|
XSTRM-64
|
Warning
|
Failed to set the 'layer selectable' property of a newly created layer-purpose pair '%s:%s'.
|
|
XSTRM-65
|
Warning
|
Failed to set the 'priority' of a newly created layer-purpose pair '%s:%s'.
|
|
XSTRM-66
|
Warning
|
Failed to update the 'packet name' of a newly created layer-purpose pair '%s:%s'.
|
|
XSTRM-67
|
Warning
|
Failed to change the validity of a newly created layer-purpose pair '%s:%s'.
|
|
XSTRM-68
|
Warning
|
Ignoring 'Load ASCII Tech File' option because target library %s is already attached' to the technology library %s.
|
|
XSTRM-69
|
Info
|
All the libraries specified in 'cds.lib' will be considered as reference libraries. This is because '-refLibList' option is specified as \XST_CDS_LIB\"."
|
|
XSTRM-70
|
Info
|
The 'Reference Library list' and the 'Keep Stream Cells' options have been used together. Any cell defined in the Stream file will not be searched in reference libraries.
|
|
XSTRM-71
|
Warning
|
The '-keepStreamCells' option has been overridden for the cells in the target library because %s.
|
|
XSTRM-72
|
Warning
|
The 'Load ASCII tech file' and 'Attach Technology Library' options have been used together. The 'Load ASCII tech file' option will be ignored.
|
|
XSTRM-73
|
Warning
|
The library name column in the cell name map file will be ignored because reference library list is not specified.
|
|
XSTRM-74
|
Error
|
Translation cannot be continued because layer mapping cannot be done. This is because the layer map is not specified by the '-layerMap' option and the technology library '%s' also does not contain '%s.layermap'. Additionally, automatic layer mapping cannot be done because the technology file is opened in read-only mode due to the library '%s' being attached to it. Use a layer map file to continue.
|
|
XSTRM-75
|
Warning
|
Target library '%s' is attached to the technology library '%s'. Therefore, the technology file is opened in read-only mode. All the undefined layer-purpose pairs will be dropped.
|
|
XSTRM-76
|
Error
|
Failed to open technology file '%s:%s' in append mode. Therefore, automatic layer mapping cannot be done. Use the layer map file to continue.
|
|
XSTRM-77
|
UN-USED
|
Failed to open the technology file '%s:%s' in append mode. All the undefined layer-purpose pairs will be dropped.
|
|
XSTRM-78
|
Error
|
Failed to load ASCII technology file %s, specified in 'Load ASCII Tech File' option.
|
|
XSTRM-79
|
Error
|
Failed to attach technology file from the library %s because a technology file already exists in the target library.
|
|
XSTRM-80
|
Error
|
The technology library '%s' specified in the 'Attach Technology Library' option does not exist.
|
|
XSTRM-81
|
Error
|
The technology library '%s' attached to the target library does not exist.
|
|
XSTRM-82
|
UN-USED
|
Failed to create the library %s.
|
|
XSTRM-83
|
Error
|
Technology file '%s' cannot be opened from the library '%s'. Ensure that the library '%s' exists and have appropriate permissions.
|
|
XSTRM-84
|
Warning
|
The 'Skip Undefined LPPs' option will be ignored because a new library is being created.
|
|
XSTRM-85
|
Warning
|
Case conversion resulted in mapping of STRUCTURE %s to cell name %s. During XStream In, translation continues by overwriting cellview data. However, to avoid the collision do not specify the case conversion option.
|
|
XSTRM-86
|
Warning
|
Memory prediction is disabled because system parameters could not be found.
|
|
XSTRM-87
|
Warning
|
Process may require more virtual memory than 32-bit system can handle. You may need to run 64-bit version of the product. Available Memory:%llu MB\tPredicted Memory:%llu MB.
|
|
XSTRM-88
|
Warning
|
Process might require more virtual memory than available on the system. Available Memory:%llu MB\tPredicted Memory:%llu MB.
|
|
XSTRM-89
|
Error
|
Failed to flatten via of viaDef '%s' at (%d, %d) in the cellview '%s/%s/%s'. XStream Out flattens a via in the specified cellview when the Flatten Vias option is used. Ensure that the via in the specified cellview is correct by opening the cellview '%s/%s/%s' and flattening the via in Virtuoso.
|
|
XSTRM-90
|
Warning
|
Process may require more virtual memory than available on the system for a process. You can increase this limit by using the 'limit' command. Available Memory:%llu MB\tPredicted Memory:%llu MB.
|
|
XSTRM-91
|
Info
|
Process may require virtual memory near to what it is available on the system for a process. You can increase this limit by using the 'limit' command. Available Memory:%llu MB\tPredicted Memory:%llu MB.
|
|
XSTRM-92
|
UN-USED
|
Process may require more data segment than available on the system for a process. You can increase this limit by using the 'limit' command. Available Memory:%llu\tPredicted Memory :%llu.
|
|
XSTRM-93
|
UN-USED
|
Process may require data segment near to available on the system for a process. You can increase this limit by using the 'limit' command. Available Memory:%llu\tPredicted Memory:%llu.
|
|
XSTRM-94
|
UN-USED
|
The cellView %s/%s is not found in the mapped library %s. This cell will not be translated, and all the instances of this cell will be unbound.
|
|
XSTRM-95
|
UN-USED
|
Creating an unbound instance of the cellview '%s/%s/%s' as the master was not found in the Stream file.
|
|
XSTRM-96
|
UN-USED
|
Creating an unbound instance because the master cellview '%s/%s' was not found in the Stream file or the specified reference library '%s'.
|
|
XSTRM-97
|
UN-USED
|
Creating an unbound instance of the cellview '%s/%s' as the master cannot be found in the mapped library '%s'.
|
|
XSTRM-98
|
UN-USED
|
Creating an unbound instance with library as target library %s because the master cellview '%s/%s' was not found in any reference library.
|
|
XSTRM-99
|
UN-USED
|
Creating an unbound instance with library as target library %s, because the master cellview '%s/%s' was not found in the Stream file or in any of the reference libraries.
|
|
XSTRM-100
|
Error
|
Instance Name %s has illegal characters. This instance is dropped.
|
|
XSTRM-101
|
Warning
|
An AREF record in the Stream file contains the illegal angle '%f', this will not be translated. Angles supported by Stream In are 0, 90, 180, 270.
|
|
XSTRM-102
|
Error
|
The '%s' option specified is invalid. View the available options using the \-help\" command and then specify the valid option."
|
|
XSTRM-103
|
Error
|
The '%s' option specified in the template file is invalid%s. View the available options using the \-help\" command and then specify the valid option."
|
|
XSTRM-104
|
Warning
|
The Stream attributes associated with some objects in the Stream file exists multiple times or have multiple properties separated by a property separator. Only the first property value is preserved and the others are ignored.
|
|
XSTRM-105
|
Info
|
Property map file contains duplicate entry for Stream attribute number '%d', object type '%s' at line number '%d'. This entry will be ignored.
|
|
XSTRM-106
|
Warning
|
The undefined layer-purpose pair are skipped because either the Skip Undefined LPPs option is specified or XStream In into an existing library is performed. To avoid skipping of undefined LPPs, ensure that the Skip Undefined LPPs option is not specified or XStream In should be performed into a new library.
|
|
XSTRM-107
|
Warning
|
Existing cells in the target library will be overwritten if the cell names in the Stream file and the target library are the same. To prevent this, %s.
|
|
XSTRM-108
|
Error
|
Layer map file is not being processed because the technology file is not available.
|
|
XSTRM-109
|
UN-USED
|
Pin text map file is not being processed because the technology file is not available.
|
|
XSTRM-110
|
UN-USED
|
Layer %s not found in the technology file.
|
|
XSTRM-111
|
UN-USED
|
Purpose %s not found in the technology file.
|
|
XSTRM-112
|
Error
|
Failed to open the user SKILL file '%s'. Check that the file exists in the run directory and that you have permission to read it.
|
|
XSTRM-113
|
Warning
|
Unable to load the SKILL file %s because of the undefined SKILL function and syntactical error. Specify the SKILL function with valid syntax and translate again.
|
|
XSTRM-114
|
Warning
|
Error in the definition of the SKILL function '%s'. The SKILL function maps the stream %s to %s. Specify the correct definition of the SKILL function and restart the translation.
|
|
XSTRM-115
|
Warning
|
Error in the definition of 'textFontMap'. Invalid font name for the Stream font number %d
|
|
XSTRM-116
|
Error
|
Illegal font '%s' mapped to the Stream font number %d. This mapping will be ignored.
|
|
XSTRM-117
|
Warning
|
Error in the definition of 'piCellNameMap'. Cell name '%s' is mapped to NULL
|
|
XSTRM-118
|
Warning
|
Error in the definition of 'piLayerMap'. No layer string returned for layer '%u' and datatype '%u'.
|
|
XSTRM-119
|
Warning
|
Error in the definition of 'piLayerMap'. No purpose string returned for layer '%u' and datatype '%u'.
|
|
XSTRM-120
|
Error
|
Translation failed because the file size of GDSII/Stream file '%s' is zero. Ensure that the correct GDSII file is specified.
|
|
XSTRM-121
|
UN-USED
|
Could not process the library '%s'.
|
|
XSTRM-122
|
UN-USED
|
|
|
XSTRM-123
|
UN-USED
|
|
|
XSTRM-124
|
UN-USED
|
|
|
XSTRM-125
|
UN-USED
|
|
|
XSTRM-126
|
UN-USED
|
|
|
XSTRM-127
|
UN-USED
|
|
|
XSTRM-128
|
UN-USED
|
|
|
XSTRM-129
|
UN-USED
|
|
|
XSTRM-130
|
Warning
|
Error occurred in the user SKILL function 'textFontMap' while mapping '%s'.
|
|
XSTRM-131
|
Warning
|
Font name '%s' mapped to invalid Stream font number '%d' by the user SKILL function 'textFontMap'. This mapping will be ignored.
|
|
XSTRM-132
|
Warning
|
Error occurred in the user SKILL function 'poCellNameMap'.
|
|
XSTRM-133
|
Warning
|
Error occurred in the user SKILL function 'poLayerMap'.
|
|
XSTRM-134
|
Warning
|
Error in the definition of 'poLayerMap'. Invalid layer number returned for layer '%s'.
|
|
XSTRM-135
|
Warning
|
Error in the definition of 'poLayerMap'. Invalid layer number returned for purpose '%s'.
|
|
XSTRM-136
|
Warning
|
Error occurred in the user SKILL function 'piTextMap' while mapping '%s'. This text will not be translated.
|
|
XSTRM-137
|
Warning
|
Error occurred in the user SKILL function 'poTextMap' while mapping '%s'. This text will not be translated.
|
|
XSTRM-138
|
UN-USED
|
|
|
XSTRM-139
|
UN-USED
|
|
|
XSTRM-140
|
Warning
|
The object map file '%s' contains an invalid record at line number '%d' and will be ignored. This is because the format of the mapping entry in the object map file '%s' is invalid. The valid mapping entry format is: <objectType objectSubType [oaLayer] strmLayer strmType [PhotomaskColor]>, where 'PhotomaskColor' is valid only when the '-enableColoring' option is set. Now, update the mapping entry and then translate again.
|
|
XSTRM-141
|
Warning
|
The object map file '%s' contains an invalid object type '%s' at line number '%d' and will be ignored. This is because the format of the mapping entry in the object map file '%s' is invalid. Update the mapping entry format to: <objectType objectSubType strmLayer strmType> and try again.
|
|
XSTRM-142
|
Warning
|
The object map file '%s' contains an invalid sub object '%s' at line number '%d' and will be ignored. This is because the format of the mapping entry in the object map file is invalid. Update the mapping entry format to: <objectType objectSubType strmLayer strmType> and try again.
|
|
XSTRM-143
|
Warning
|
Object map file %s contains multiple entries for objectType:sub-objectType '%s:%s' at line number '%d'. Only the first record will be used.
|
|
XSTRM-144
|
Warning
|
Stream attribute number '%d' specified in property mapping file at line '%d' is not within range, '0-125'. This entry will be ignored.
|
|
XSTRM-145
|
Warning
|
The structure name '%s' has been changed to '%s' by the translator. This could be because multiple cells with the same cell name exist in different libraries, the same cell name has been mapped to multiple cell names, or the cell name length is greater than the '%d' that was specified using the '-respectGDSIINameLimit' or '-gdsCellNameLength' option.
|
|
XSTRM-146
|
Error
|
Cell map file contains a duplicate stream structure name '%s' at line number '%d'. This record in the cell map file will be ignored.
|
|
XSTRM-147
|
Warning
|
The property string associated with the object type '%s' exceeds the maximum permissible length of '%d' characters. Therefore, the property string will be truncated.
|
|
XSTRM-148
|
Error
|
Failed to open the via map file '%s'. Check that the file exists in the run directory and that you have permission to read it.
|
|
XSTRM-149
|
Error
|
Failed to create the via map file '%s' in the run directory. Check that you have permission to create this file.
|
|
XSTRM-150
|
Warning
|
The via map file, '%s' already exists. It will be overwritten.
|
|
XSTRM-151
|
Warning
|
Failed to find via definition '%s' in the tech file. This entry in the viaMap file will be ignored.
|
|
XSTRM-152
|
Warning
|
A polygon at (%d, %d) will be dropped because OpenAccess does not support a polygon which contains less than three coordinates. The number of distinct points required to create a polygon should be three. Rectify the source of the GDSII file and translate again.
|
|
XSTRM-153
|
Error
|
Failed to open object map file '%s'. Check that the file exists in the run directory and that you have permission to read it.
|
|
XSTRM-154
|
Warning
|
The object map file does not contain any mapping for the OpenAccess object '%s' and the sub-object '%s'. Therefore, these objects in the design will not be translated. To enable the translation of these objects in the Stream file, provide a valid mapping in the object map file.
|
|
XSTRM-155
|
Warning
|
Ignoring the Stream layer-datatype pair '%d:%d' at row '%d' in the object map file '%s' because it is also defined in the layer map file. Additionally, shapes in GDS on '%d:%d' with properties indicating they were translated from objects in the OpenAccess database will be translated back to objects. The remaining shapes will be translated to shapes.
|
|
XSTRM-156
|
Warning
|
The entry at line number '%d' is duplicate in the '%s' layerMap file. Therefore, this entry will be ignored during translation.
|
|
XSTRM-157
|
Warning
|
The '%s' SKILL procedure has generated a structure name '%s' that has been changed to '%s' by the translator. This could be because multiple cells with the same cell name exist in different libraries, the same cell name has been mapped to multiple cell names, or the cell name length is greater than the '%d' that was specified using the '-respectGDSIINameLimit' or '-gdsCellNameLength' option.
|
|
XSTRM-158
|
Error
|
Error in the definition of the SKILL procedure '%s'. The SKILL procedure maps the Pcell submaster name to a NULL string. Correct the definition of the SKILL procedure for this error and restart the translation.
|
|
XSTRM-159
|
Warning
|
Error in the definition of the SKILL procedure '%s'. Either the evaluation of %s has failed or it has returned an invalid SKILL list. Correct the SKILL procedure and restart the translation
|
|
XSTRM-160
|
Warning
|
The design has an area halo blockage with owner instance. Property map file is needed to preserve instance name as a property on the instance. Specify property map file at '-propMap' option.
|
|
XSTRM-161
|
Error
|
Property map file is needed to preserve area halo blockages. Property map file is not specified. Specify Property map file at '-propMap' option.
|
|
XSTRM-162
|
Info
|
You have not used the '-viaMap' option. If the OpenAccess design has native oaVia instances, use the '-viaMap' option for preserving oaVia instances in a XStream Out - XStream In round trip. Using the '-viaMap' option improves performance and VM usage of applications using the Streamed-In design.
|
|
XSTRM-163
|
Info
|
You have not used the '-viaMap' option. If a viaMap file, corresponding technology file or technology library exist, then use the '-viaMap' option for creating oaVia instances in the Streamed-In library. Using the '-viaMap' option improves performance and VM usage of applications using the Streamed-In design.
|
|
XSTRM-164
|
Warning
|
%s. The %s will be dropped.
|
|
XSTRM-165
|
Error
|
Multiple stream structures are getting mapped to the same cell '%s' and view '%s' in the target library '%s'. Ensure that you have specified all required reference libraries and updated the cell name map file to avoid many-to-one mapping. Also ensure that input stream file is valid.
|
|
XSTRM-166
|
Error
|
Translation Failed - %s\nIf problem persists, contact the Cadence Customer Support.
|
|
XSTRM-167
|
Warning
|
Failed to open the sub-master. Internal automatic name mapping will be done for the sub-master %s as the SKILL function %s cannot be called for this sub-master.\nIf problem persists, contact the Cadence Customer Support.
|
|
XSTRM-168
|
Warning
|
The structure, %s, in the stream file is getting mapped to a cellview ('%s:%s') that already exists in the target library '%s'. Ignoring this cellview.
|
|
XSTRM-169
|
Warning
|
The structure, %s, in the stream file is getting mapped to a cellview ('%s:%s') that already exists in the target library '%s'. Overwriting this cellview in the target library.
|
|
XSTRM-170
|
Warning
|
The '-noObjectProp' option is used without the '-objectMap' option therefore it will be ignored. To use the '-noObjectProp' option you must specify an object map file using the '-objectMap' option.
|
|
XSTRM-171
|
Info
|
The '-noObjectProp' and the '-objectMap' options have been used together. Therefore, no property data is written to the stream file at property attribute 126 on the stream Boundary record.
|
|
XSTRM-172
|
Warning
|
Font map file %s exists in the technology library but is not readable. No font mapping will be done.
|
|
XSTRM-173
|
UN-USED
|
|
|
XSTRM-174
|
Warning
|
The target library is already attached to technology library '%s'. Therefore, '-techRefs' option will be ignored
|
|
XSTRM-175
|
Warning
|
'%s' and '%s' are two mutually exclusive options that have been used together. The '%s' option will override the '%s' option.
|
|
XSTRM-176
|
UN-USED
|
Translation Failed.\nIf problem persists, contact the Cadence Customer Support.
|
|
XSTRM-177
|
Warning
|
Invalid stream version '%d' specified. Valid values are 3,5 and 6. The translator will use version '%d' as default.
|
|
XSTRM-178
|
Warning
|
Stream version '%d' and '%s' option have been used together. BOX record in stream file is supported only for stream version 5 and onwards. The translator will ignore '%s' option. If you want to translate rectangles in the design as BOX record in stream file, specify version as '%d' or do not specify '-strmVersion' option.
|
|
XSTRM-179
|
Error
|
XStream In has detected a conflict in the technology database graph. This could be because the technology library of the target library has conflict in its technology database graph or the specified reference technology libraries have a conflict with the technology library of the target library. Resolve the conflict manually before running the XStream In application.
|
|
XSTRM-180
|
Info
|
You have not used the '-objectMap' option. The design has instance(s) of at least one of following OpenAccess objects: oaBlockage, oaBoundary, oaRow, and oaMarker. Any information about these objects will not be translated into the generated stream file. Use the '-objectMap' option to translate/preserve these objects using XStream.
|
|
XSTRM-181
|
Warning
|
The '%s' label map file contains an unknown layer '%s' at line '%d'. XStream Out will ignore this record in the label map file and continue to run. To fix this error, define the '%s' layer name in the technology file and restart XStream Out.
|
|
XSTRM-182
|
Warning
|
The '%s' label map file contains an unknown purpose '%s' at line '%d'. XStream Out will ignore this record in the label map file and continue to run. To fix this error, define the '%s' purpose name in the technology file and restart XStream Out.
|
|
XSTRM-183
|
Warning
|
The '%s' label map file contains an invalid record at line '%d'. XStream Out will ignore this record in the label map file and continue to run.
|
|
XSTRM-184
|
Warning
|
The '%s' label map file contains a duplicate record for the '%s:%s' OpenAccess layer-purpose pair at line '%d'. XStream Out will ignore this record in the label map file and continue to run.
|
|
XSTRM-185
|
Warning
|
The value '%s' is specified for the 'Convert Pin To' option simultaneously with the '%s' option. XStream Out will ignore the '%s' option and continue to run.
|
|
XSTRM-186
|
Warning
|
The value 'text' or 'geometryAndtext' is specified for the 'Convert Pin To' option simultaneously with the 'Label Map' option. XStream Out will map data according to the label map file specified in the 'Label Map' option.
|
|
XSTRM-187
|
UN-USED
|
|
|
XSTRM-188
|
Warning
|
OpenAccess does not support coincident or collinear paths. A path with either coincident or collinear points is encountered at (%d, %d). The coincident or collinear points will be eliminated and an equivalent path will be created during translation.
|
|
XSTRM-189
|
Warning
|
A path with an invalid begin or end extension value is encountered at (%d, %d). This path will be ignored during translation.
|
|
XSTRM-190
|
Warning
|
OpenAccess does not support coincident or collinear polygons. A polygon with either coincident or collinear points is encountered at (%d, %d). The coincident or collinear points will be eliminated and an equivalent polygon will be created during translation.
|
|
XSTRM-191
|
Warning
|
Found a polygon with self-intersecting points at the origin (%d, %d). This polygon will be translated without any changes. Correct the source of translation if the self-intersecting polygon is not required.
|
|
XSTRM-192
|
Warning
|
Found a path with self-intersecting points at the origin (%.4f, %.4f). This path will be translated without any changes. Correct the source of translation if the self-intersecting path is not required.
|
|
XSTRM-193
|
Warning
|
An open polygon is encountered at (%d, %d). This polygon will be ignored during translation.
|
|
XSTRM-194
|
Warning
|
OpenAccess does not support paths that have less than two coordinates. A path starting at (%d, %d) has less than two coordinates and therefore will be ignored during translation.
|
|
XSTRM-195
|
UN-USED
|
Value '%d' specified for option '%s' is %s than the valid range that is %s. %s value for this option has been set.
|
|
XSTRM-196
|
Warning
|
The design has %s with octagonal extensions in the cellview '%s/%s/%s'. These paths will be written as PATHTYPE1 (circular) in the Stream/GDSII file. You can retain the geometry of these %s by using the Convert Path to Polygon option.
|
|
XSTRM-197
|
Warning
|
The Stream/GDSII files has some PATH records with PATHTYPE 1 (circular). Virtuoso workbench will view extensions of these paths as octagonal. There could be potential problems and you should correct these at the source of the Stream/GDSII file.
|
|
XSTRM-198
|
Warning
|
The Stream layer-datatype '%d:%d' pair at row number '%d' in the object map file '%s' is already mapped. This entry in object map file will be ignored.
|
|
XSTRM-199
|
Warning
|
The Stream layer-datatype '%d:%d' is mapped to sub-object '%s' of layerBlockage which is not supported in DFII.
|
|
XSTRM-200
|
Warning
|
XStream In is running in automatic layer mapping mode and hence '-skipUndefinedLPP' option will be ignored. Specify layer map file name for XStream In to respect '-skipUndefinedLPP' option.
|
|
XSTRM-201
|
Warning
|
A path with self-intersecting points is encountered at (%d, %d). This path will be translated as is. Correct the source of the translation if the self-intersecting path is not required.
|
|
XSTRM-202
|
Warning
|
The '-topCell' option is used without any view name. During XStream Out, the translator will translate all the views of maskLayout type for each of the specified topCell(s). Specify the view name that needs to be translated.
|
|
XSTRM-203
|
Warning
|
The '-view' name is not specified. During XStream Out, the translator will translate all the views of maskLayout type of the specified library. Specify the view name that needs to be translated.
|
|
XSTRM-204
|
Warning
|
The following issue occurred while processing cellview '%s': %s The corresponding structure definition will not be added to the GDSII/stream file, and therefore, importing the GDSII file may result in unbound instances. %s
|
|
XSTRM-205
|
Info
|
The Stream layer-datatype pair %d:%d is mapped to layer-purpose pair %s:%s, which does not exist in the technology library. All shapes on XStream layer-datatype pair %d:%d will be skipped. To avoid skipping shapes on the undefined LPPs, do not specify the '-skipUndefinedLPP' option.
|
|
XSTRM-206
|
Warning
|
%s The path would be written in Stream file as is. To resolve this, fix the reported path in the input design and run the translator again.
|
|
XSTRM-207
|
Warning
|
%s The path would be created with the dimensions in Stream file. To resolve this, fix the source from which the Stream file is generated and then run the translator again with the new stream file.
|
|
XSTRM-208
|
Error
|
License initialization failed due to some internal error. Try again and if problem persists, contact Cadence Customer Support.
|
|
XSTRM-209
|
Error
|
The required license for XStream translator could not be found. Either the license server is down or the license is not available. Ensure that the valid license is available.
|
|
XSTRM-210
|
Error
|
Failed to initialize %s subsystem. For more information, contact the Cadence customer support.
|
|
XSTRM-211
|
Error
|
The argument with option '%s' could not be found. This is because the value for the argument is not specified. Specify the valid value and then try again.
|
|
XSTRM-212
|
Error
|
The value for the scaleTextHeight argument is invalid. This is because the value of the argument is less than zero. Specify the positive integer value and then try again.
|
|
XSTRM-213
|
Error
|
The value for argument '%s' is invalid. This is because the argument '%s' contains a value other than upper, lower, or preserve. Specify the value for the argument '%s' as upper, lower, or preserve and then try again.
|
|
XSTRM-214
|
Error
|
The value for '-strmTextNS' is invalid. Valid values are cdba, verilog, or vhdl. Specify the correct value and translate again.
|
|
XSTRM-215
|
Error
|
The option in the command line is missing. This is because either both '-strmFile' and '-library' options are not specified or the '-cellListFile' option is not specified. Specify '-strmFile' and '-library' options or the '-cellListFile' option and then translate again.
|
|
XSTRM-216
|
Error
|
|
|
XSTRM-217
|
Info
|
Reading the %s file, %s
|
|
XSTRM-218
|
Error
|
The parsing of the template file, '%s', cannot be completed. This is because the undefined UNIX environment variable, '%s', is used in the value at line number '%d'. Ensure that the UNIX environment variable is defined and then try again.
|
|
XSTRM-219
|
UN-USED
|
The value for the maxCellsInTargetLib argument is invalid. This is because the value of the argument is less than zero. Specify the positive integer value of the argument and try again.
|
|
XSTRM-220
|
Info
|
Translating STRUCTURE %s as cellView %s/%s/%s.
|
|
XSTRM-221
|
Info
|
Cell contains a zero width path. The zero width path will not be translated.
|
|
XSTRM-222
|
Info
|
%s
|
|
XSTRM-223
|
Info
|
%ld. Translating %s %s/%s/%s as STRUCTURE %s.
|
|
XSTRM-224
|
Warning
|
Unable to find library %s
|
|
XSTRM-225
|
UN-USED
|
Error in reading template file %s
|
|
XSTRM-226
|
Warning
|
File name for %s is not specified
|
|
XSTRM-227
|
Warning
|
Error in opening file %s
|
|
XSTRM-228
|
Error
|
Failed to open object map file '%s'. Check that the file exists in the run directory and that you have permission to read it.
|
|
XSTRM-229
|
Error
|
Failed to create viaDef in the technology library as the technology library is attached to the target library. ViaDefs are being created because '-detectVias' option is specified. Detach the technology library from the target library and use '-techRefs' option to create incremental technology or don't specify the '-detectVias' option.
|
|
XSTRM-230
|
Error
|
Failed to create viaDef in the technology library as it is read-only. ViaDefs are being created because '-detectVias' option is specified. Change the permissions of the technology library or don't specify the '-detectVias' option.
|
|
XSTRM-231
|
Error
|
Pcell evaluation failed for '%s' because the Pcell SKILL code contains either a syntax error or an unsupported XStream function. Check the standard output or the Virtuoso log file for more information. Cadence recommends correcting the Pcell SKILL code to resolve the issue. However, to ignore these errors and continue the translation, you may use the '-ignorePcellEvalFail' option.
|
|
XSTRM-232
|
Warning
|
Pcell evaluation failed for '%s' because the Pcell SKILL code contains either a syntax error or an unsupported XStream function. Check the standard output or the Virtuoso log file for more information. The translation will continue because the '-ignorePcellEvalFail' option is enabled, but the output should be checked to ensure it meets your requirements.
|
|
XSTRM-233
|
Error
|
The creation of a run directory '%s' has failed. Ensure that you have appropriate permissions to create the directory.
|
|
XSTRM-234
|
Info
|
Translation completed. '%d' error(s) and '%d' warning(s) found.
|
|
XSTRM-235
|
Warning
|
A LayerBlockage will be dropped because the layer used for the layerBlockage is not defined in the technology library. Ensure that the correct technology library is used and then translate again.
|
|
XSTRM-236
|
Info
|
A path with a rounded extension, an acute angle or a length segment less than half width is encountered at (%d, %d). This path will be written as a boundary record in the GDS file.
|
|
XSTRM-237
|
Warning
|
The layer-purpose pair '%u:%u' does only exist with \floating keyword\". The \"floating\" layer will also be used to map \"non floating\" shapes."
|
|
XSTRM-238
|
Warning
|
The layer-purpose pair '%s:%s' does only exist with \floating keyword\". The \"floating\" layer will also be used to map \"non floating\" shapes."
|
|
XSTRM-239
|
Warning
|
The value '%d' specified for the '-viaCutArefThreshold' option is less than 15. The recommended value of the option is greater than or equal to 15. Therefore, the value of the option will be defaulted to 15.
|
|
XSTRM-240
|
Warning
|
Property %s will not be put on merged PATH in the GDS as another pathSeg has already has this property.You have specified '-mergePathSegToPath' option and translating properties.
|
|
XSTRM-241
|
Error
|
Unable to create the ASCII technology file '%s' in the run directory. Ensure that you have the write permission to create this file.
|
|
XSTRM-242
|
Error
|
Unable to create the LayerMap file '%s' in the run directory. Ensure that you have the write permission to create this file.
|
|
XSTRM-243
|
UN-USED
|
Unable to open the Cadence default technology library \%s\". Ensure that the library has been installed properly."
|
|
XSTRM-244
|
Warning
|
The default mapping, without any optional fields, for layer-purpose pair '%u:%u' is not defined in the layer map file. All the objects on this layer-purpose pair that map to the default mapping will be ignored.
|
|
XSTRM-245
|
Warning
|
The default mapping, without any optional fields, for layer-purpose pair '%s:%s' is not defined in the layer map file. All the objects on this layer-purpose pair that map to the default mapping will be ignored.
|
|
XSTRM-246
|
Warning
|
Ignoring the record at line number '%d' in the layer map file '%s'. This is because the qualifier \cutsize\" specified for the layer '%s' is not valid for the layer's material type '%s'. Valid material types for the qualifier are cut
|
|
XSTRM-247
|
Warning
|
Layer map file '%s' contains an invalid record for OpenAccess layer-purpose pair '%s:%s' and Stream layer-datatype pair '%d:%d' at line number '%d' and will be ignored. This is because the \floating\" qualifier is specified for the %s purpose whose type is neither fill nor oaFillOPC."
|
|
XSTRM-248
|
Error
|
Failed to open label map file '%s'. Check that the file exists in the run directory and that you have permission to read it.
|
|
XSTRM-249
|
Error
|
The cellListFile does not contain any valid records to process. Ensure that the cellListFile contains valid records in the following format: <LibraryName> <CellName> <ViewName> <GDSFileName>
|
|
XSTRM-250
|
Error
|
Failed to create output directory '%s'. Ensure that you have appropriate permissions to create this directory, or provide a different output directory.
|
|
XSTRM-251
|
Error
|
Failed to open cell list file '%s'. Check that the file exists in the run directory and you have appropriate permissions to read it.
|
|
XSTRM-252
|
Warning
|
The cellListFile contains invalid record at line number '%d'. This record in cellListFile will be ignored. Ensure that each line in cellListFile contains all the four entries in the following format: <LibraryName> <CellName> <ViewName> <GDSFileName>
|
|
XSTRM-253
|
Warning
|
Multiple records with different library names exist in the cellListFile and will be ignored. Presently, only one library name is supported in the cellListFile.
|
|
XSTRM-254
|
Warning
|
The '-view' option in the command line is missing and '*' is specified in the view entry of the cellListFile. The entry will be ignored because the value of the '-view' option that needs to replace '*' is missing. Specify the '-view' option or view name in cellListFile.
|
|
XSTRM-255
|
Warning
|
The cellListFile contains duplicate entries for cellView '%s/%s/%s' and will be ignored. Ensure that only one record for each cellView exists in the cellListFile.
|
|
XSTRM-256
|
Warning
|
The cellView '%s/%s/%s' specified in the cellListFile does not exist on-disk, and entry will be ignored. Ensure that the cellView exists and the path of the library '%s' is specified in library definition file.
|
|
XSTRM-257
|
Warning
|
Library name specified in the cellListFile is different than specified with '-library' option and will be ignored. Presently, only one library name is supported in the cellListFile.
|
|
XSTRM-258
|
Warning
|
The '-library' option in the command line is missing and '*' is specified in the lib entry of the cellListFile. This entry will be ignored because the value of the '-library' option that needs to replace '*' is missing. Specify the '-library' option or lib name in cellListFile.
|
|
XSTRM-259
|
Warning
|
The property map file '%s' contains invalid record at line number '%d'. The valid object types are: Dot, Line, Path, Polygon, Rect, Text, ArrayInst, ScalarInst, Arc, Donut, Ellipse, PathSeg, Route, Marker, Row, AreaBoundary, PRBoundary, SnapBoundary, ClusterBoundary, AreaBlockage, AreaHalo, LayerBlockage, and LayerHalo. Specify the valid object types and try again.
|
|
XSTRM-260
|
Error
|
The option in the command line is missing. This is because the '-strmFile' option is not specified and either of the '-strmTechGen' or '-library' option is not specified. Specify the '-strmFile' option and either of the '-strmTechGen' or '-library' option and then translate again.
|
|
XSTRM-261
|
Warning
|
The object map file does not contain any mapping for the '%s' LayerBlockage on layer '%s'. Therefore, this LayerBlockage in the design will not be translated. To enable the translation of this LayerBlockage in the Stream file, provide a valid mapping in the object map file.
|
|
XSTRM-262
|
Error
|
Failed to translate cellView, '%s/%s/%s'. This is because the cellView is opened by another process in the edit mode. Close the cellView and then translate again.
|
|
XSTRM-263
|
Error
|
Failed to translate cellView, '%s/%s/%s'. This is because the '%s/%s/%s/layout.oa' file does not have appropriate permissions. Set appropriate permissions on the file and then translate again.
|
|
XSTRM-264
|
Error
|
Failed to translate cellView, '%s/%s/%s' - '%s'.\nIf problem persists, contact the Cadence Customer Support.
|
|
XSTRM-265
|
Info
|
The Property map file '%s' contains multiple property names for Stream attribute number '%d', object type '%s'. This may cause problem while XStream In.
|
|
XSTRM-266
|
Warning
|
The property map file '%s' contains a record with more than one property name at line number '%d'. Only the first property name will be considered in XStream In and others will be ignored.
|
|
XSTRM-267
|
Warning
|
%s Ensure that the referenced cell exists and library is defined in the cds.lib file.
|
|
XSTRM-268
|
UN-USED
|
|
|
XSTRM-269
|
Warning
|
Layer map file '%s' contains value, which is not within the range '0 - %d' for Stream layer at line number '%d'. However, this entry will not be ignored and all objects will be translated.
|
|
XSTRM-270
|
Warning
|
Layer map file '%s' contains value, which is not within the range '0 - %d' for Stream datatype at line number '%d'. However, this entry will not be ignored and all objects will be translated.
|
|
XSTRM-271
|
UN-USED
|
Value '%d' specified for option '%s' is %s than the valid range that is %s. %s value for this option has been set.
|
|
XSTRM-272
|
UN-USED
|
Ignoring the numThreads option because the stream file specified is a compressed stream file, and compressed file is not supported with multiple threads.
|
|
XSTRM-273
|
Info
|
Translation failed. '%d' error(s) and '%d' warning(s) found.
|
|
XSTRM-274
|
Info
|
To improve performance of flattening Pcell instances the preserving Pcell pins is not done during XStream Out. This is because preserving Pcell pins is not required as the value 'geometry' or 'ignore' is specified for the Convert Pin To option.
|
|
XSTRM-275
|
Info
|
Number of vertexes in the '%s' with starting point (%d, %d) on layer '%u' is %d.%s This number exceeds the maximum limit, %d, defined by '%s'. The '%s' will be chopped into smaller %ss during XStream Out translation.
|
|
XSTRM-276
|
Error
|
Failed to chop '%s' with starting point (%d, %d) on layer '%u'. Delete or chop this '%s' and continue translation.
|
|
XSTRM-277
|
Error
|
Failed to open excludeMapToVia file '%s'. Check that the file exists in the run directory and that you have permission to read it.
|
|
XSTRM-278
|
Warning
|
The '%s' excludeMapToVia file contains an invalid record at line '%d'. XStream In will ignore this record in the excludeMapToVia file and continue to run.
|
|
XSTRM-279
|
Error
|
Translation failed due to an internal error. This problem occurred while creating FIFO. Translate again and if problem persists, contact the Cadence Customer Support.
|
|
XSTRM-280
|
Info
|
The output file will be a compressed file because the file name has extension .gz
|
|
XSTRM-281
|
Info
|
The input file '%s' will be read as a compressed file because the file name has extension .gz
|
|
XSTRM-282
|
Info
|
The '-dbuPerUU' option will be ignored because the value (%d) does not match the 'dbuPerUU' value (%d) in technology database '%s'. Using the 'dbuPerUU' value from the technology database.
|
|
XSTRM-283
|
Warning
|
Data precision might be lost because the value (%d) set for the '-dbuPerUU' option does not match the 'dbuPerUU' value (%d) in technology database '%s'.
|
|
XSTRM-284
|
Warning
|
DbuPerUU (%d) specified in the technology database or using '-dbuPerUU' is not divisible by the value (%d) set in the GDSII file. This can cause loss in data precision during translation.
|
|
XSTRM-285
|
Warning
|
Data precision is lost while scaling a point. This is because of difference in the original point (%d, %d) and the scaled point (%d,%d).
|
|
XSTRM-286
|
UN-USED
|
The '-numThreads' option will be ignored. This is because the value of the argument is less than 1. The value of the argument should be greater than or equal to 1.
|
|
XSTRM-287
|
Info
|
The STRUCTURE '%s' in the input GDSII/Stream file will not be translated. This is because either the '-refLibList' option is used and the cellview is available in the reference library '%s' or the STRUCTURE is not mapped to the target library using the cell map file/piCellMap SKILL function. Therefore, all the instances of the cellview will be referenced from '%s/%s/%s'.
|
|
XSTRM-288
|
Info
|
Performing automatic layer mapping because either the layer mapping information is not provided or the XST_AUTO_LM value is used with the '-layerMap' option. Additionally, the '%s' file has been generated and the mapping information has been added to it.
|
|
XSTRM-289
|
Info
|
Performing automatic layer mapping because either the layer mapping information is not provided or the XST_AUTO_LM value is used with the '-layerMap' option.
|
|
XSTRM-290
|
UN-USED
|
%s
|
|
XSTRM-291
|
Info
|
Output GDSII/Log file '%s' already exists. Therefore, XStream Out will create a backup file with the name, '%s.bak' as the '-backupGdsLogFiles' option is specified.
|
|
XSTRM-292
|
Warning
|
Both output GDSII/Log file '%s' and it's backup file, '%s.bak' already exist. Therefore, XStream Out will remove the existing '%s.bak' and create a new backup file, '%s.bak' as the '-backupGdsLogFiles' option is specified.
|
|
XSTRM-293
|
Error
|
Translation stopped. Both output GDSII/Log file '%s' and it's backup file, '%s.bak' already exist. Therefore, XStream Out will try to remove the existing '%s.bak' and create a new backup file, '%s.bak' as the '-backupGdsLogFiles' option is specified. However, the '%s.bak' file does not have the write permission. Ensure that the '%s.bak' file have the appropriate permissions and then try again.
|
|
XSTRM-294
|
Warning
|
Both '-append' and '-noOverwriteCell' options have been specified. The '-noOverwriteCell' option will be ignored.
|
|
XSTRM-295
|
Warning
|
Data precision is lost while scaling an integer value. This is because of the difference in the original value (%d) and the scaled value (%d).
|
|
XSTRM-296
|
Warning
|
Data precision is lost while scaling an integer value. This is because of the difference in the original value (%u) and the scaled value (%u).
|
|
XSTRM-297
|
Warning
|
The pin information of the GDS shape is ignored. This is because the GDS shape is created as an OpenAccess object, and a pin cannot be attached to an OpenAccess object.
|
|
XSTRM-298
|
UN-USED
|
The Stream layer-datatype '%d:%d' pair at row number '%d' in the object map file '%s' is also defined in the layer map file. Remove this duplicate entry either from the layer map file or object map file to avoid the XStream Out-XStream In round-trip issue.
|
|
XSTRM-299
|
Error
|
The specified library '%s' is not a valid primary virtual memory library created by XStream In. Use the 'xstInGetVMLibs' SKILL function to get a list of valid primary virtual memory libraries created by XStream In.
|
|
XSTRM-300
|
Error
|
The specified destination path '%s' does not exists. Ensure that the destination path exists.
|
|
XSTRM-301
|
Error
|
The directory '%s' required to save the virtual memory library already exists at the specified destination path '%s'. Specify a destination path that does not have a directory with the virtual memory library name.
|
|
XSTRM-302
|
Error
|
The technology library '%s' attached to the library '%s' does not exist. Ensure that the library '%s' is attached to a valid technology library.
|
|
XSTRM-303
|
Error
|
Failed to open the '%s' file. Check that the file exists and that you have the permission to modify it.
|
|
XSTRM-304
|
Warning
|
Disk space is low (< %dMB of free space) and may fill up during translation. To avoid any data loss, free up some disk space.
|
|
XSTRM-305
|
Warning
|
Writing PATH record with the coincident points or less than two points at (%d %d) because the oaDesign contains a line with such points.
|
|
XSTRM-306
|
UN-USED
|
|
|
XSTRM-307
|
Warning
|
The value for \text\" or \"geometryAndtext\" is specified for the Convert Pin To field simultaneously with the \"Label Map File\" found in the technology library. XStream Out will map data according to the \"Label Map File\" picked from the technology library."
|
|
XSTRM-308
|
Warning
|
The '%s' option will be ignored in command line. This option is only available in GUI. Use the \-help\" command to view the options available in command line."
|
|
XSTRM-309
|
Warning
|
The '%s' option specified in the template file will be ignored in command line. This option is only available in GUI. Use the \-help\" command to view the options available in command line."
|
|
XSTRM-310
|
Warning
|
The '-disableLocking' option is now obsolete. XStream In, by default, translates the library in non-locking mode. Use the '-enableLocking' option to translate the library in locking mode.
|
|
XSTRM-311
|
Warning
|
The '-disableLocking' option specified in the template file is now obsolete. XStream In, by default, translates the library in non-locking mode. Use the '-enableLocking' option to translate the library in locking mode.
|
|
XSTRM-312
|
Info
|
The '-enableLocking' option is selected so the output cellviews in the Cadence database will be separately locked. The translation may take more time as locking is enabled.
|
|
XSTRM-313
|
Warning
|
The '-disableLocking' option specified in the xstInSetField/xstInGetField SKILL function or streamInKeys SKILL list is now obsolete. XStream In, by default, translates the library in non-locking mode. Use the '-enableLocking' option to translate the library in locking mode.
|
|
XSTRM-314
|
Warning
|
The value '%s' specified for the '%s' option is invalid. This is because the value of the argument is either negative, zero, or any other invalid value. Specify a valid non-zero positive float value for the '%s' option and translate again.
|
|
XSTRM-315
|
Warning
|
The cellview '%s/%s/%s' has a label with multiple lines. This label will be translated as is. If a multiple lines label is not required, correct the label in the source file.
|
|
XSTRM-316
|
Warning
|
The STRUCTURE '%s' has a TEXT record with multiple lines. This TEXT record will be translated as is. If a multiple lines TEXT record is not required, correct the TEXT record in the source file.
|
|
XSTRM-317
|
Info
|
The '%s/%s/%s' has a pathSeg with diagonal orientation, or end style as custom or chamfer at (%d, %d). This pathSeg will be translated as a boundary record in the GDS file during XStream Out.
|
|
XSTRM-318
|
Info
|
The Property map file '%s' contains duplicate entries for property name '%s', object type '%s' at line number '%d'. Since the same entry already exists for Stream attribute number '%d', this entry will be ignored.
|
|
XSTRM-319
|
Warning
|
The %s map file '%s' contains color aware mapping(s) and will not be visible in GUI. This is because the 'Enable Coloring' option is not selected. Select the 'Enable Coloring' option to display these entries in the table else these entries will be ignored during translation.
|
|
XSTRM-320
|
Warning
|
The %s map file '%s' contains a color aware entry at line number '%d' and this entry will be ignored. To consider this entry specify the '-enableColoring' option to do color aware mapping.
|
|
XSTRM-321
|
Error
|
Translation cannot be continued as the '-enableColoring' option is used, but the layer map file is not found. This is because either the -layerMap option is not specified or technology does not have the layer map file. Use a valid layer map file and then translate again.
|
|
XSTRM-322
|
Error
|
Translation cannot be continued as the '-enableColoring' option is used, but technology is not found. Provide a technology either by using the '-attachTechFileOfLib' option, or ensure that library either has valid technology or is attached to the valid technology in case the target library already exist and then translate again.
|
|
XSTRM-323
|
Warning
|
The layer map file '%s' contains inconsistent color aware entry at line number '%d' and this entry will be ignored. This is because layer '%s' does not support either coloring or Photomask color '%s'.
|
|
XSTRM-324
|
Warning
|
Colored shapes are found on layer-purpose pair '%u:%u' with photomask color '%s' and color state '%s', and a non-color-aware mapping is done for these shapes. This is because, color mapping is not specified for photomask color '%s', color state '%s', and layer-purpose pair '%u:%u'.
|
|
XSTRM-325
|
Warning
|
Colored shapes are found on layer-purpose pair '%s:%s' with photomask color '%s' and color state '%s', and a non-color-aware mapping is done for these shapes. This is because, color mapping is not specified for photomask color '%s', color state '%s', and layer-purpose pair '%s:%s'.
|
|
XSTRM-326
|
Warning
|
Connected pathSegs on colorable layers will not be merged and each pathSeg will be written as separate PATH record in GDS. This is because both '-enableColoring' and '-mergePathSegsToPath' options have been specified. Therefore, the '-mergePathSegsToPath' option will not be considered for the pathSegs on colorable layers.
|
|
XSTRM-327
|
Warning
|
Both '-enableColoring' and '-viaCutArefThreshold' options have been specified. The '-viaCutArefThreshold' option is not supported with the '-enableColoring' option. Therefore, the '-viaCutArefThreshold' option will be ignored.
|
|
XSTRM-328
|
Info
|
The '-enableColoring' and '-topCell' options are specified but '-arrayInstToScalar' option is not specified. Additionally, the layer map file has unlocked mapping entries. The GDS file will be generated with the effective color for the unlocked color shapes. However, array instances might be written as multiple SREF records in the GDS file because the effective color requires color variant generation.
|
|
XSTRM-329
|
Warning
|
The GDS file will be generated without the effective color for the unlocked color shapes. This is because the '-topCell' option is not specified, although the '-enableColoring' option is specified and the layer map file has unlocked mapping entries. The effective color requires color variant generation that depends on the hierarchy context. To generate the GDS file with the effective color, define the hierarchy context using the '-topCell' option.
|
|
XSTRM-330
|
Info
|
The layer map file '%s' contains a duplicate entry for OpenAccess layer-purpose pair '%s:%s' and Stream layer-datatype pair '%d:%d' at line number '%d'.
|
|
XSTRM-331
|
Info
|
The '-enableColoring' and '-topCell' options have been specified, but the layer map file does not have any unlocked mapping entry. Therefore, all the unlocked color shapes in the OpenAccess database will be translated according to noncolor-aware mapping in the GDS file.
|
|
XSTRM-332
|
Warning
|
Encountered a cellview '%s/%s/%s' that has a view type different from maskLayout. It will not be saved on the disk.
|
|
XSTRM-333
|
Warning
|
The '-enableColoring' option will be ignored during %s. This is because there is no color entry in the layer map and the object map file.
|
|
XSTRM-334
|
Error
|
Translation has been aborted because the '-compress' option has not been specified with the '-compressLevel' option. When the '-compressLevel' option is used, the '-compress' option must be specified.
|
|
XSTRM-335
|
Error
|
Translation has been aborted because invalid value, '%s' has been specified for the '-compressLevel' option. Valid values for the '-compressLevel' option are between 1 and 9.
|
|
XSTRM-336
|
Warning
|
The '%s' option will be ignored during XStream %s because the '%s' option has not been specified.
|
|
XSTRM-337
|
UN-USED
|
|
|
XSTRM-338
|
Error
|
The translation terminated because the cellview '%s/%s/%s' contains colored data that is incompatible with this version of the translator. Use an advanced node version of the translator (for example ICADV12.1) to process this data.
|
|
XSTRM-339
|
Error
|
The translation terminated because the GDSII/Stream file '%s' contains colored data that is incompatible with this version of the translator. Use an advanced node version of the translator (for example ICADV12.1) to process this data.
|
|
XSTRM-340
|
Error
|
Failed to attach technology '%s' to the library '%s' because read permission is not set for the database of at least one of the libraries or technologies defined in cds.lib. Check that you have appropriate permissions and try again.
|
|
XSTRM-341
|
Error
|
Translation failed while processing '%s' because of the following reason: %s %s
|
|
XSTRM-342
|
Warning
|
The input Stream/GDSII file is empty; therefore, XStream In has no structures to translate.
|
|
XSTRM-343
|
Warning
|
The input Stream/GDSII file is empty and has no structures that can be translated. The preexisting library \'%s\' will remain as it is.
|
|
XSTRM-344
|
UN-USED
|
The colors set for the locked color shapes in the master design are ignored and the colors set for the locked hierarchical color shapes in the top cell are used instead.
|
|
XSTRM-345
|
UN-USED
|
The design contains unlocked color shapes and also has an overlay cell. The unlocked color shapes have been mapped based on the unlocked color mappings defined in the layer map file.
|
|
XSTRM-346
|
Warning
|
The '-%s' option is no longer supported. Use the '-writeMode' option with value '%s' instead.
|
|
XSTRM-347
|
Warning
|
The '%s' option specified in the template file is no longer supported. Use the 'writeMode' option with value '%s' instead.
|
|
XSTRM-348
|
Warning
|
The '%s' option specified in the 'xstInSetField' or 'xstInGetField' SKILL functions or the streamInKeys SKILL list is no longer supported. Use the 'writeMode' option with value '%s' instead.
|
|
XSTRM-349
|
Error
|
An invalid value '%s' was specified for the '-writeMode' option. Set '-writeMode' to either 'noOverwrite', 'overwrite', 'append', or 'rename' and run the command again.
|
|
XSTRM-350
|
Warning
|
The '-overwriteRootCells' option has been ignored because it is valid only when '-writeMode' is set to 'rename'.
|
|
XSTRM-351
|
UN-USED
|
Value '%d' specified for option '%s' is %s than the valid range that is %s. %s value for this option has been set.
|
|
XSTRM-352
|
Warning
|
The '-exportHierarchicalColorLocks' option is now obsolete. XStream Out, by default, exports the hierarchical color locks.
|
|
XSTRM-353
|
Warning
|
The 'exportHierarchicalColorLocks' option specified in the template file is now obsolete. XStream Out, by default, exports the hierarchical color locks.
|
|
XSTRM-354
|
Warning
|
The technology library '%s' contains colored data that is incompatible with this version of the translator and should be used ideally with an advanced node version of the translator (for example ICADV12.1). Make sure that you are using the correct version.
|
|
XSTRM-355
|
Warning
|
The 'translateUnmappedLPP' option has been ignored during XStream %s because it does not impact automatic layer mapping. Use this option with the 'layerMap' file or the layer mapping SKILL function '%s'.
|
|
XSTRM-356
|
Info
|
Applied automatic layer mapping to the layer-purpose pair '%u:%u'.
|
|
XSTRM-357
|
Info
|
Applied automatic layer mapping to the layer-purpose pair '%s:%s'.
|
|
XSTRM-358
|
Warning
|
The new purpose '%s' will be created in memory only and will not be saved to the technology because the technology has been opened in read-only mode.
|
|
XSTRM-359
|
Warning
|
The new layer '%s' will be created in memory only and will not be saved to the technology because the technology has been opened in read-only mode.
|
|
XSTRM-360
|
Warning
|
The new layer-purpose pair '%s:%s' will be created in memory only and will not be saved to the technology because the technology has been opened in read-only mode.
|
|
XSTRM-361
|
Info
|
Ignoring the '-translateUnmappedLPP' option because the '-skipUndefinedLPP' option has been defined.
|
|
XSTRM-362
|
Error
|
Translation cannot be continued. This is because the '-translateUnmappedLPP' option is used, which requires creation of layers, purposes, and LPPs, and technology library '%s' is opened in read-only mode due to the library '%s' being attached to it. To continue, either do not specify the '-translateUnmappedLPP' option or specify a target library that contains 'tech.db' or ITDB.
|
|
XSTRM-363
|
Warning
|
The technology library has been modified during XStream In translation. Cannot save the changes in the technology file because it is open in read-only mode.
|
|
XSTRM-364
|
Warning
|
Ignoring the layer-datatype pair '%s:%s' in the layer map file '%s' at line number '%d' because the technology library is read-only and the layer-datatype pair is not defined in the technology file.
|
|
XSTRM-365
|
Warning
|
The layer-datatype pair '%s:%s' in 'piLayerMap' will be ignored. This is because technology is read-only and the layer-datatype pair is not defined in the technology file. This layer-datatype pair is now mapped automatically for XStream In and XStream Out.
|
|
XSTRM-366
|
Warning
|
The '-strmTechGen' option requires only a GDSII file as its input. Therefore, ignoring all options other than '-strmTechGen' and '-strmFile.'
|
|
XSTRM-367
|
Warning
|
Ignoring the '-strmTechGen' option because the '-library' option has been defined.
|
|
XSTRM-368
|
Warning
|
The '-enableIncrementalImport' option is ignored during XStream In because the library specified is not the same as the primary library used for previous incremental import project. To continue in the same incremental import project, specify the '%s' library as the primary library. You can also start a new incremental project with a different primary library by running the translation in a new directory or by deleting the '.cadence/geoTrans' directory present in the current directory.
|
|
XSTRM-369
|
Warning
|
The instance '%s' instantiated in '%s/%s/%s' with origin at (%d, %d) is unplaced but will be written to Stream/GDSII file '%s'. If you do not want to export unplaced instances, use the option '-noOutputUnplacedInst'.
|
|
XSTRM-370
|
UN-USED
|
|
|
XSTRM-371
|
Error
|
The translation failed because automatic layer mapping cannot be done. This is because none of the stream %s numbers from the valid range ('0-65535') is available. Define the %s you want to map in the layerMap file and start the translation again.
|
|
XSTRM-372
|
Info
|
XStream Out is propagating the locks because it is in the 'lock same color group' mode.
|
|
XSTRM-373
|
Info
|
XStream Out will not be in the 'lock same color group' mode. This is because %s.
|
|
XSTRM-374
|
Error
|
The design '%s' contains array instance '%s' of design '%s' with %d columns and %d rows. This does not comply with GDS format. Split this array instance such that number of columns and rows of the resultant array instances does not exceed 65536, and run translation again.
|
|
XSTRM-375
|
Warning
|
The design '%s' contains array instance '%s' of design '%s' with %d columns and %d rows. This is incompatible with some GDS readers, which only allow a maximum of 32768 AREF columns and rows. To avoid issues during translation, split this array instance such that the number of columns and rows of the resultant instances does not exceed 32768.
|
|
XSTRM-375
|
Warning
|
%s
|
|
XSTRM-376
|
Info
|
The '-translateUnmappedLPP' option overrides any entry with 'ignoreLPP' qualifier specified in layermap file '%s'.
|
|
XSTRM-377
|
Error
|
The translation failed because the option '-guiHistory' has been specified but no successful translation was done from the XStream %s GUI. Remove the '-guiHistory' option and rerun the translation.
|
|
XSTRM-378
|
UN-USED
|
|
|
XSTRM-380
|
UN-USED
|
|
|
XSTRM-381
|
Info
|
The '-enableColoring' and '-mapAllColorToLocked' options have been enabled. Unlocked shapes will be mapped according to the locked color mappings. Unlocked colored mappings will be ignored in the layer map file.
|
|
XSTRM-382
|
UN-USED
|
Translation has been stopped because the layer map file '%s' contains insufficient number of locked color-aware mappings for layer '%s'. Provide locked color-aware mappings for all the 'color masks' or 'photo masks' for this layer and translate again.
|
|
XSTRM-383
|
Warning
|
Found a rectangle with zero-area at the origin (%.4f, %.4f). This rectangle will be translated without any changes. Correct the source of translation if the zero-area rectangle is not required.
|
|
XSTRM-384
|
Info
|
The number of cells in library \%s\" exceeds the limit of %d. A new library \"%s\" will be created."
|
|
XSTRM-385
|
Warning
|
The '-numThreads' option is no longer supported in XStream In. The number of cores in the CPU will be detected automatically and an appropriate number of threads will be used for translation.
|
|
XSTRM-386
|
Warning
|
The 'numThreads' option specified in the template file is no longer supported in XStream In. The number of cores in the CPU will be detected automatically and an appropriate number of threads will be used for translation.
|
|
XSTRM-387
|
Warning
|
The 'numThreads' option specified in the xstInSetField or xstInGetField SKILL function or the streamInKeys SKILL list is no longer supported in XStream In. The number of cores in the CPU will be detected automatically and an appropriate number of threads will be used for translation.
|
|
XSTRM-388
|
Warning
|
The '-detectVias' option is no longer supported in XStream In. The vias will be detected automatically. Use the '-noDetectVias' option if via detection is not required.
|
|
XSTRM-389
|
Warning
|
The '-detectVias' option specified in the template file is no longer supported in XStream In. The vias will be detected automatically. Use the '-noDetectVias' option if via detection is not required.
|
|
XSTRM-390
|
Warning
|
The '-detectVias' option specified in the xstInSetField or xstInGetField SKILL function or the streamInKeys SKILL list is no longer supported in XStream In. The vias will be detected automatically. Use the '-noDetectVias' option if via detection is not required.
|
|
XSTRM-391
|
Warning
|
Running the replay function in support mode. This replay function was created using an older release, such as IC6.1.6 or ICADV12.1 and is now obsolete. Regenerate the replay function using the redesigned XStream GUI.
|
|
XSTRM-392
|
Warning
|
Detected old replay functions that are not supported in the current release. The XStream GUI has been redesigned and any settings through replay functions from an older release, such as IC6.1.6 or ICADV12.1 will be ignored. Regenerate the replay function using the redesigned XStream GUI.
|
|
XSTRM-393
|
Warning
|
Ignoring color aware entries in the via map file '%s'. To consider these entries during translation, specify the '-enableColoring' option.
|
|
XSTRM-394
|
Warning
|
Ignoring color aware entries in the via map file '%s'. To consider these entries for via preservation with coloring information, use an advanced node version of the translator (for example ICADV12.2), and specify the '-enableColoring' option.
|
|
XSTRM-395
|
Warning
|
Ignoring via submaster record '%s' in the via map file '%s' because it contains an invalid color attribute parameter.
|
|
XSTRM-396
|
Warning
|
Ignoring rectangles with inverted bounding box because translating them may result in an invalid GDS file.
|
|
XSTRM-397
|
Warning
|
Ignoring option '%s' %sbecause it is incompatible with this version of the translator. Use this option with an advanced node version of the translator (for example ICADVM20.1).
|
|
XSTRM-398
|
UN-USED
|
Value '%d' specified for option '%s' is %s than the valid range that is %s. %s value for this option has been set.
|
|
XSTRM-399
|
Warning
|
The STRUCT '%s' generated for '%s/%s/%s' in GDS is empty because either the design is empty or no shape or object was translated.
|
|
XSTRM-400
|
Warning
|
Both option '-flattenVias' and CDS environment variable 'xstIgnoreCoveredViaShapes' have been specified. The 'xstIgnoreCoveredViaShapes' variable is not supported with the '-flattenVias' option. Therefore, the 'xstIgnoreCoveredViaShapes' variable will be ignored.
|
|
XSTRM-401
|
Error
|
Translation failed because bounding box coordinates of the array instance %s in the cellview '%s/%s/%s' exceed the limits allowed in the GDSII format (-2147483647, 2147483648). Use a smaller DBU value or use the OASIS format to export the design.
|
|
XSTRM-402
|
Info
|
Ignoring %s file '%s' in the technology library because it is not readable.
|
|
XSTRM-403
|
Warning
|
The '-flattenViaShapesAsViaPurp' option is no longer supported. Use '-outputViaShapesToViaPurp' with '-flattenVias' to flatten shapes of vias to via purpose.
|
|
XSTRM-404
|
Warning
|
The 'flattenViaShapesAsViaPurp' option specified in template file is no longer supported. Use 'outputViaShapesToViaPurp' with 'flattenVias' to flatten shapes of vias to via purpose.
|
|
XSTRM-405
|
Warning
|
The 'flattenViaShapesAsViaPurp' option specified in the xstOutSetField or xstOutGetField SKILL function or the streamOutKeys SKILL list is no longer supported. Use 'outputViaShapesToViaPurp' with 'flattenVias' to flatten shapes of vias to via purpose.
|
|
XSTRM-406
|
Warning
|
Both locked and unlocked shapes for '%s:%s:%s'%s are mapped to same Stream layer-datatype '%d:%d' in layer map file '%s' at line number '%d'.
|
|
XSTRM-407
|
Warning
|
The top cell '%s' contains a modified Concurrent Layout cellview. Changes in the top and hierarchical Concurrent Layout design partition views are not automatically exported from virtual memory to GDS. To export these changes, right-click in the Concurrent Layout assistant and choose 'XStream Out from VM for DRC'.
|
|
XSTRM-408
|
Warning
|
Option '%s' specified in the template file is invalid in XStream %s GUI. Run \%s -help\" at command prompt to view list of available options and then specify the valid option in the template file."
|
|
XSTRM-409
|
Warning
|
Both '-noDetectVias' and '%s' options have been specified. The '%s' option works when via detection is enabled but the '-noDetectVias' option disables via detection. Therefore, the '%s' option will be ignored.
|
|
XSTRM-410
|
Warning
|
Layer map file '%s' contains a duplicate entry for Stream layer-datatype '%d:%d' at line '%d' which maps the shapes to '%s:%s:%s:%s' but is already mapped to '%s:%s:%s:%s'. This entry will be ignored during translation.
|
|
XSTRM-411
|
Error
|
Failed to open the flatten Pcell exclusion file '%s'. Ensure that the file exists in the run directory and that you have permission to read it.
|
|
XSTRM-412
|
Info
|
Cannot flatten instances of Pcell master '%s/%s/%s' in cellView '%s/%s/%s' because the Pcell master is specified in the flatten Pcell exclusion file '%s'.
|
|
XSTRM-413
|
Error
|
Translation failed because the specified technology is non-IC type. This is not supported by XStream Out.
|
|
XSTRM-414
|
Error
|
An invalid value '%s' was specified for the '-curvedPathEndCapStyle' option. Set '-curvedPathEndCapStyle' to 'round', 'square', or 'flush' and run the command again.
|
|
XSTRM-415
|
Error
|
An invalid value '%s' was specified for the '-curvedShapeEdgePlacement' option. Set '-curvedShapeEdgePlacement' to either 'inside' or 'outside' and run the command again.
|
|
XSTRM-416
|
Warning
|
Value '%d' specified for the '-curvedShapeNumSides' option is not a multiple of 4, which may cause discretization to generate asymmetric geometry. For symmetric geometries, use a value that is a multiple of 4.
|
|
XSTRM-417
|
Warning
|
Value '%d' specified for the '-curvedShapeNumSides' option is higher than 512. This may require more time and memory during discretization and might result in a larger GDS file. Use a number larger than 512 for this option only if it is really needed.
|
|
XSTRM-418
|
Info
|
DbuPerUU (%d) specified in the technology database or using '-dbuPerUU' does not match with the value (%d) set in the GDSII file.
|
|
XSTRM-419
|
Warning
|
Exported a shape with starting point (%d, %d) and '5' vertices. The shape will be represented using '6' points in the GDS. Although 'maxVertices' is set to '%d', the shape cannot be chopped further because it has any-angle edges. Chop the shape manually and translate again.
|
|
XSTRM-420
|
UN-USED
|
Translation Failed - %s Enable the '-detectOverflow' option and try again.
|
|
XSTRM-421
|
Warning
|
Ignoring option '-pinLabelPurp' because purpose '%s' specified for this option is not found in the technology library. Ensure that the specified purpose exists in the technology library and translate again.
|
|
XSTRM-422
|
Warning
|
Cannot find layer mapping for the layer-purpose pair '%s:%s' in the layer map file. Exported pin labels will have same layer-purpose pair as the pin shape. To avoid this issue, ensure that the layer-purpose pair exists in the layer map file corresponding to the purpose 'pinLabelPurp'.
|
|
XSTRM-423
|
Warning
|
Ignoring the Stream layer-datatype pair '%d:%d' in the layer map file because it is also defined in the object map file '%s' at row '%d' and a user-specified setting gives the object map file higher precedence over the layer map file.
|
|
XSTRM-424
|
Error
|
Translation Failed. %s Ensure that the specified cellview exists on disk and that you have permission to open it and then rerun the translation.
|
|
XSTRM-425
|
Warning
|
%s The corresponding structure definition will not be added to the GDSII file. Importing the GDSII file may result in unbound instances. Ensure that the master cellview exists and the specified library is defined in the library definition file.
|
|
XSTRM-426
|
Info
|
%ld. Translating cut shape of standard via '%s' as STRUCTURE %s.
|
|
XSTRM-427
|
Info
|
Based on current hardware configuration, running XStream Out translation in multi-threaded mode with %d threads.
|
|
XSTRM-428
|
Error
|
%s failed due to unknown reason. Run the translator again. If the problem persists, contact Cadence Customer Support for assistance.
|
|
XSTRM-429
|
Warning
|
Cannot translate because an existing non-VM library has been specified. Specify either a non-existing library or a pre-existing VM library, created using XStream In VM mode and translate again.
|
|
XSTRM-430
|
Info
|
%s
|
